本文共 3161 字，大约阅读时间需要 10 分钟。
一般情况下使用"telnet ip port"判断端口通不通，其实测试方法不止这一种，还有很多种方法，下面小编给大家分享了几种方法，具体内容请往下看：
准备环境
启动一个web服务器，提供端口.
[wyq@localhost ~]$ python -m SimpleHTTPServer 8080
Serving HTTP on 0.0.0.0 port 8080 ...
用其它web服务器提供端口也一样，由于python比较方便，这里就用它
1、使用telnet判断
telnet是windows标准服务，可以直接用；如果是linux机器，需要安装telnet.
用法: telnet ip port
1)先用telnet连接不存在的端口
[root@localhost ~]# telnet 10.0.250.3 80
Trying 10.0.250.3...
telnet: connect to address 10.0.250.3: Connection refused #直接提示连接被拒绝
2)再连接存在的端口
[root@localhost ~]# telnet localhost 22
Trying ::1...
Connected to localhost. #看到Connected就连接成功了
Escape character is '^]'.
SSH-2.0-OpenSSH_5.3
a
Protocol mismatch.
Connection closed by foreign host.
2、使用ssh判断
ssh是linux的标准配置并且最常用，可以用来判断端口吗？
用法: ssh -v -p port username@ip
-v 调试模式(会打印日志).
-p 指定端口
username可以随意
1)连接不存在端口
[root@localhost ~]# ssh 10.0.250.3 -p 80
ssh: connect to host 10.0.250.3 port 80: Connection refused
[root@localhost ~]# ssh 10.0.250.3 -p 80 -v
OpenSSH_5.3p1, OpenSSL 1.0.1e-fips 11 Feb 2013
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 10.0.250.3 [10.0.250.3] port 80.
debug1: connect to address 10.0.250.3 port 80: Connection refused
ssh: connect to host 10.0.250.3 port 80: Connection refused
2)连接存在的端口
[root@localhost ~]# ssh ... -p
a
^]
^C
[root@localhost ~]# ssh ... -p -v
OpenSSH_.p, OpenSSL ..e-fips Feb
debug: Reading configuration data /etc/ssh/ssh_config
debug: Applying options for *
debug: Connecting to ... [...] port .
debug: Connection established.
debug: permanently_set_uid: /
debug: identity file /root/.ssh/identity type -
debug: identity file /root/.ssh/identity-cert type -
debug: identity file /root/.ssh/id_rsa type -
debug: identity file /root/.ssh/id_rsa-cert type -
debug: identity file /root/.ssh/id_dsa type -
debug: identity file /root/.ssh/id_dsa-cert type -
a
^C
不用-v选项也可以咯
3、使用wget判断
wget是linux下的下载工具，需要先安装.
用法: wget ip:port
1)连接不存在的端口
[root@localhost ~]# wget ...:
---- ::-- http://.../
Connecting to ...:... failed: Connection refused.
2)连接存在的端口
[root@localhost ~]# wget ...:
---- ::-- http://...:/
Connecting to ...:... connected.
HTTP request sent, awaiting response...
4、使用端口扫描工具
[root@localhost ~]# nmap ... -p
Starting Nmap . ( http://nmap.org ) at -- : CST
Nmap scan report for ...
Host is up (.s latency).
PORT STATE SERVICE
/tcp closed http
MAC Address: B:A::CF:FD:D (Unknown)
Nmap done: IP address ( host up) scanned in . seconds
[root@localhost ~]# nmap ... -p
Starting Nmap . ( http://nmap.org ) at -- : CST
Nmap scan report for ...
Host is up (.s latency).
PORT STATE SERVICE
/tcp open http-proxy
MAC Address: B:A::CF:FD:D (Unknown)
Nmap done: IP address ( host up) scanned in . seconds
[root@localhost ~]# nmap ...
Starting Nmap . ( http://nmap.org ) at -- : CST
Nmap scan report for ...
Host is up (.s latency).
Not shown: closed ports
PORT STATE SERVICE
/tcp open ssh
/tcp open rpcbind
/tcp open http-proxy
/tcp open unknown
MAC Address: B:A::CF:FD:D (Unknown)
Nmap done: IP address ( host up) scanned in . seconds
总结
提供端口服务，则使用了tcp协议，上面是以web服务器为例。如果服务器是更简单的tcp服务器，三个工具同样适用.
三个工具的共同点是：1.以tcp协议为基础；2.能访问指定端口. 遵循这两点可以找到很多工具.
一般在windows下使用telnet比较方便，linux下个人就比较喜欢用wget.
转载地址：http://hnudy.baihongyu.com/